@KISS_MY_CONVERSE
that puppy is CLEAN... I'm gonna buy that case.
@diana.winter
A few notes on the case from my own experience: A 420mm crossflow radiator almost but doesn’t quite fit in the top. A regular 420mm does work with the motherboard in the lower position, but that makes cabling more difficult, so I feel like a 360mm with the MB in the upper position makes the most sense. Likewise, a 360mm crossflow in the side bracket might be possible but probably not worth the tradeoffs for most builds. The vertical GPU mount needs its own anti-sag device to avoid deforming the back of the case when using heavy cards. In the lowest position, you might get away with a shim between it and the bottom fans. The riser cable on the vertical mount is also too long unless it is mounted in the lowest position and the motherboard is the upper position. Otherwise, the ribbon is either pressed up against the backplate of the card or the heatsink for the chipset/VRMs. The cable management door does not close completely when using larger PSUs. The side panel still fits overtop, so it isn’t a dealbreaker, but worth mentioning. The drive cage area is large enough to support a pump/res combo like an FLT80, but the mounting holes are slightly too narrow for a standard 80mm mounting bracket. Only an issue if you want a triple rad loop without a distro plate covering the front panel or a pump and reservoir blocking your view of those sweet LCD fans. Not the case itself, but related: I tried the strimmer RGB cables and while I want to love them, I don’t think they work in this case. The 12vhpwr cable needs a right angle connector to avoid potential bending issues with the side glass and the 24-pin cable is way too long. I could just about plug it straight into my PSU if it had the right connector, but as it’s an extension cable, it just makes cable management that much harder.
@venomvenom6971
I think what makes this attractive would be for left handed setup and the seamless perpendicular alignment between the glass panels. Much like the nzxt h9 flow but with the choice for it to be on the left side. Rgb wise would be more of an add on to the rgb lovers. I personally prefer this over the original o11d mainly because of the seamless glass panel intersection.
@Stigness23
Preordered mine today, cant wait. Im hoping they release the piece to let you move the USB hub to the top of the case like the previous EVO
@Rad_Pug
I get this case next week. Still trying to figure out some of the other components. A distro plate is very intriguing. Nice video.
@SarKo-4
Well I am happy to say I will be buying this case. I will also be getting the new lian li 120 tl lcd reverse blade fans as well.
@daviddesrosiers1946
Some curious differences between this case and the original O-11D Evo. I like that they made more room in the cable bay. It's one f my few gripes about the Evo. If you have a lot of cabling in your rig, the cable bay of the Evo can become rather cramped directly behind the PSU, especially with PSUs above a 1000W. I like how Lian Li extended the RGB on the sides of the fans all the way to the edge, unlike the original SL INF fans.
@Big_Swanga
Man...I really think you have all then best general questions that everyone wants to know!! Thank you. When mine is done I'd like to show you!! 😂😂 bout to finally finish!!
@anub1s15
the swapable PSU location is also nice if you want to go the custom cable route and would like your cables as short as possible without to much spaghetti everywhere. atleast in the 011D with a corsair SF750 if you reverse mount it in the top all your connectors are where you would want them. EPS is top left of the PSU, besides that is the 24 pin and below that is your PCI-E and Sata nothing needs to cross over another cable to go where it needs to go it's awsome. and the plate it free's up is where i've housed my Fan/RGB/Pump management. (hope the EVO RGB leaves enough clearance i have my eye on it for a future upgrade seems like everything i love about the 011D with better airflow and minor tweaks
@Browniiie92
Ending worked for a sub, great job on this review!
@focibc
Fanatic content and really I appreciate some cheeky b roll shots!
@BGBATKA
Buying a build using this case tomorrow for a full ALL WHITE build! Lian Li EVO RGB, MSI MPG Z790 Edge Wifi, i9-13900k, 4080 Super, can't wait !
@Dragonytez
6:30 Thanks for saying this. I was driving myself nuts on how these trays wouldn't negate the fans / radiator on the other side. I was looking for some sort of other purpose to them, but I guess I just have to leave them off.
@gsambolin
This is going to sound weird but the voice from Provoked Prawn just make you want to watch video over video over video. New PC Builder here, I found a great video on the NZXT Kraken AIO Radiator and it was worth it. NEW SUB !!
@wiIdcattm
If I didn't just brought the Dynamic a few months ago, I'd buy this one. Particularly because I have to my system in the reverse built due to where my desk is, but the reverse built with a 3090 is uncomfortable too close to the motherboard because my motherboard is a tad bigger. This latest incarnation of the Dynamic seems to address that. Unfortunately, I have a rule of thumb not to buy a new case for a couple of years. If someone told me they'd give me this, though, I'd be all over it.
@ArtFiendz
incredible. I'm going to be building my daughter a PC in a month or so and she likes my current lian li o11 dynamic so I'm going to swap my build to one of these. I hope they aren't sold out at that point. lol. I'm actually really stoked for this case
@marcel1463
A dream case, thanks for the detailed video.
@cheezyjokester
I just bought this case to replace my Lian Li Lancool II. It sucks in so much dust through the front I am constantly cleaning it and the radiator in the front. No dust filter means a ton of dust and I was at my whit end. This is going to be exciting not to mention had it reversed since it sits on my left.
@Riggan201
It's an awesome Case, but what i don't get, why they missed dust filters.. the mesh by itself is just not good enough 😢
@TheProvokedPrawn